Searchresult

VC – Compact rod sensor

Compact stainless steel rod sensor for use under extreme conditions...

MCK – miniature sensor

...0-1 V or digital (similar to I²C) Very small Compact sensor with cable connection or plug-in connection Or as miniature rod shaped sensor, 12 mm...

Weather guard

...from the floor does not reach the sensor. Ø 20 mm and Ø 15 mm For Probe sensors Ø 20 mm andwith clamping sleeve 00.502,...

VC/11 Compact sensor (ammonia-resistant)

...sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element...

VR, VR.D – Compact sensor with robust head

...humidity and temperature in air and other non-aggressive gases. Capacitive MELA® sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable...

(T)FG80 – Humidity Temperature Sensor

Typs: FG80 - Humidity Sensor TFG80 - Humidity Temperature Sensor (T)FG80H with passive resistance output up to 10 kOhm (T)FG80J with active current or voltage...

eStat20 – electronic hygrostat with remote sensor

...Accuracy H.: ±2 % RH Accuracy T.: ±0.35 K 2 configurable switching outputs 2 permanent signal outputs Long-term stability Easy to install Exchangable sensor part...

eStat20 DUO – electronic hygro-thermostat with remote sensor

...Accuracy H.: ±2 % RH Accuracy T.: ±0.35 K 2 configurable switching outputs 2 permanent signal outputs Long-term stability Easy to install Exchangeable sensor part...

(T)FG120 – Indoor Humidity Temperature Sensor

Typs: FG120 – Humidity Sensor TFG120 – Humidity Temperature Sensor...

eStat20 – Sensor und Hygrostat in einem!

Sensor und Hygrostat in einem! Mit zwei individuell konfigurierbaren Relais zur Überwachung der Feuchte sowie zwei Analogausgängen für Feuchte und Temperatur eignet er sich ideal...

HSF Humidity sensor

with capacitive Mela® humidity sensor element for condensation control IP 65...

LP – probe

The LP is the L-series probe sensor. These economical transmitters, with a highly dynamic capacitive humidity sensor chip, are primarily optimised for ambient roomconditions and...

BZ – Transmitter with remote probe

...the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures long-term stability,...

AW – combined with probes of the S series

...series. Capacitive MELA® sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the...

BK – duct mounted

...MELA® sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor...

AK combined with probes of the S series

...MELA® sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor...

AW with remote probe

...Capacitive MELA® sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA®...

ZC and ZC.H – Transmitter with remote probe

...with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures long-term...

GC-ME wall mounted – meteorology version

...with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures long-term...

ZC.D, ZC.HD – with remote probe, pressure-resistant up to 25 bar

...capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures long-term stability, resistance to dew...

ATEX KC.Ex – duct mounted

...sensor part with a sintered filter (both made from stainless steel), mounted on a robust aluminium pressure die-cast housing (transmitter component). These sensors measure with...

DK – duct mounted

Humidity Sensor DKF Humidity Temperature Sensor DKK Excellent transmitter - highly accurate and easy to install. The industrial versions DK (duct mounted version) can be...

IAK – Probes with plug-in connection

...sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element...

IRK – Probes with robust head

...K. Capacitive MELA® sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the...

ATEX GC.Ex – wall mounted

...2D. The sensors consist of a sensor part with a sintered filter (both made from stainless steel), mounted on a robust aluminium pressure die-cast housing...

GC – wall mounted

...sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element...

KC – duct mounted

...ideally suited to industrial applications, e.g. drying processes. Capacitive MELA® sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance...

Protective filter Ø 15 mm

Filters and protective baskets are used to adapt sensors to the different locations where they are deployed. They protect the sensor from mechanical damage caused...

Condensation controller – FGO / FGS

Humidity sensor to prevent the building of condensed water...

PC and PC.S probe

...sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures long-term stability, resistance to dew formation, minimal...

PM15P – digital probe

...heads (PMU) can be switched within seconds, allowing processes to run continuously with virtually no interruption. Capacitive humidity sensor Use of capacitive humidity sensor elements...

LK – duct mounted

...sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures long-term stability, resistance to dew formation, minimal...

PC-ME and PC.S-ME outdoor version

...with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures long-term...

KL – duct mounted

...with gauze filters as standard. Other filters are available on request. Capacitive MELA® sensorchips Equipped with the highly dynamic capacitive MELA® sensor element, the sensor...

IVK – Stainless steel probes with plug-in connection (modbus)

...high air speeds. Implementing the Modbus RTU protocol stack makes these sensors bus compatible. Capacitive MELA® sensorchips Equipped with the highly dynamic capacitive MELA® sensor...

WL – indoor

...Equipped with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures...

ITK – Stainless steel probes (modbus)

...with the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures long-term...

BW – wall mounted

...the highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures long-term stability,...

(T)FK120J – Indoor

FK120J Humidity Sensor TFK120J Humidity-Temperature Sensor Transmitters for semi-industrial and industrial applications. These humidity and temperature sensors are very robust, providing highly accurate measurements across...

RC – Probe with robust head and RC-ME meteorology

...highly dynamic capacitive MELA® sensor element, the sensor provides reliable performance across the full humidity range. Using the MELA® sensor element ensures long-term stability, resistance...

Protective filter Ø 20 mm

Filters and protective baskets are used to adapt sensors to the different locations where they are deployed. They protect the sensor from mechanical damage caused...

Protective filter Ø 12 mm

...to adapt the sensors to the different locations of use. They also protect the sensor from particle bombardment at higher air speeds and certain deposits....

S series SVKA probes

Operating temp. up to 85 °C Accuracy: ±1,5 % RH On-site calibration IP65 Stainless steel sensor tube Modular, can be combined...

DW – wall mounted

...Accuracy Temperature: ±0,3 K (with current output) On-site calibration Electronics based on micro controller Easy to install With the highly dynamic capacitive MELA® sensor element...

(T)FM80 OEM – duct version

Accuracy: ±2.5 % RH very high accuracy in high humidity washable measurement element with the robust Polyga® humidity measuring element long-term stability high-grade steel sensor...

S series SZKA probes with cable

Operating temp. up to 200 °C Accuracy : ±1,5 % RH On-site calibration IP65 Stainless steel sensor tube Modulair, can be combined...

Capacitive MELA® sensor chip

Protective filter Ø 20 mm for outdoor applications

...Protects the sensor element against high air speeds and dusty conditions. Operating temperature range: -50...150°C IP65 ZE22 - Same as type ZE21, but coarse-pored (max....

LI – indoor

...can also be used in moderate industrial conditions. Equipped with the highly dynamic capacitive MELA® sensor element for the entire range of relative humidity measurement....

LW – wall mounted

...temperature are used to calculate enthalpy, absolute humidity, air/water mixing ratio or wet bulb temperature. Equipped with the highly dynamic capacitive MELA® sensor element for...

PL – probe

Humidity and temperature sensors optimised for HVAC...

eStat10 – electronic hygrostat

Indoor electronic humidistat - combined device - sensor and hygrostat in one Hygrostat with two individually configurable relays and two additional analogue outputs (for humidity...

eStat10 DUO – electronic hygro-thermostat

Combined device – sensor and hygrostat in one Hygro-Thermostat with two individually configurable relays and two additional analogue outputs (for humidity and temperature) are suitable...

(T)FK80J – duct version

FK80J Humidity Sensors TFK80J Humidity-Temperature Sensors The sensors of the FK Series are very robust humidity and temperature sensors, providing highly accurate measurements across the...

Filter for Polyga duct mounted version

Filter for Polyga duct mounted version, PTFE, two-part, for sensor types HG80 and FG80 recommended for extreme operating conditions. Recommended for air speeds between 8...

Wall console for duct version

Wall console for sensors, made of plastic, for mounting duct version Ø 20 mm. With a mounting sleeve (Article Nr. 00.502) also suitable for sensor...

Digital combi-controller EDJ3

Input: 2 x ... 20mA Output H.: 2 N/O contacts Output T.: 2 N/O contacts Supply voltage 230 V AC With integrated sensor power supply...

Job offers

At our medium-sized company, you won’t just be a number — you’ll make a real difference. With us, you’ll help shape the future of sensor...